# HZG

 2018-04-2713:37 [PUBDB-2018-01869] Journal Article et al Formation of block-copolymer-templated mesoporous silica Journal of colloid and interface science 521, 183 - 189 (2018) [10.1016/j.jcis.2018.03.032]   In situ attenuated total reflectance Fourier transform infrared spectroscopy is used to monitor the chemical evolution of the mesoporous silica SBA-15 from hydrolysis of the silica precursor to final silica condensation after the particle formation. Two silica precursors, tetraethyl orthosilicate (TEOS) or sodium metasilicate (SMS) were used, and the effects of additive (heptane and NH$_4$F) concentrations were studied. [...] 2018-04-2712:48 [PUBDB-2018-01868] Journal Article et al Effects of laser processing on the transformation characteristics of NiTi: A contribute to additive manufacturing Scripta materialia 152, 122 - 126 (2018) [10.1016/j.scriptamat.2018.04.024]   Laser additive manufacturing of NiTi generates complex microstructural features not fully understood yet. Thermalsimilarities between lasermicrojoining and laser additivemanufacturing, enables correlating the effect of thelaser on the material in both processes. [...] Fulltext: PDF; Restricted: PDF PDF (PDFA); 2018-04-2614:19 [PUBDB-2018-01858] Journal Article et al The grain boundary pinning effect of the μ phase in an advanced polycrystalline $\gamma /\gamma ′$ Co-base superalloy Journal of alloys and compounds 753, 333 - 342 (2018) [10.1016/j.jallcom.2018.04.204]   A grain boundary pinning phase was introduced into a $\gamma /\gamma ′$ Co-base superalloy by the addition of Mo. Theintermetallic phase was identified as m phase (Co,Ni,Cr)$_7$(W,Mo)$_6$ by high-energy X-ray diffraction andenergy-dispersive X-ray spectroscopy in the transmission electron microscope. [...] Restricted: PDF PDF (PDFA); 2018-04-2610:39 [PUBDB-2018-01856] Journal Article et al A synchrotron X-ray and electron backscatter diffraction based investigation on deformation and failure micro-mechanisms of monotonic and cyclic loading in titanium Materials science and engineering / A 726, 143 - 153 (2018) [10.1016/j.msea.2018.04.036]   Synchrotron X-ray diffraction technique has been used to estimate defect structure in terms of dislocationdensity, crystallite size and micro-strain in commercially pure titanium subjected to tension and cyclic deformationin stress and strain control mode. Statistical analysis of micro-texture data collected from electronbackscatter diffraction approximately from the same region as that of synchrotron X-ray has been used to correlateorientation dependent micro-strain and dislocation density with deformation microstructure and microtexture.Two different orientations, namely, A with prismatic-pyramidal and B with basal orientation along theloading axis has been considered. [...] Restricted: PDF PDF (PDFA); 2018-04-2510:22 [PUBDB-2018-01848] Journal Article et al Influence of Annealing on Microstructure and Mechanical Properties of a Nanocrystalline CrCoNi Medium-Entropy Alloy Materials 11(5), 662 (2018) [10.3390/ma11050662]   An equiatomic CrCoNi medium-entropy alloy was subjected to high-pressure torsion.This process led to a refinement of the microstructure to a grain size of about 50 nm, combined witha strong increase in the materials hardness. Subsequently, the thermodynamic stability of the mediumentropy alloy was evaluated by isothermal and isochronal heat treatments. [...] OpenAccess: PDF PDF (PDFA); 2018-04-2510:07 [PUBDB-2018-01847] Journal Article et al Influence of quasicrystal I-phase on twinning of extruded Mg-Zn-Y alloys under compression Acta materialia 151, 271 - 281 (2018) [10.1016/j.actamat.2018.03.060]   The interaction of the I-phase with twins during compression has been studied in a Mg-6Zn-1Y (wt.%)alloy using the combination of Synchrotron Radiation Diffraction and Acoustic Emission experimentsduring compression tests. The I-phase occurs as coarse particles at grain boundaries and nanosizedprecipitates within magnesium grains. [...] Restricted: PDF PDF (PDFA); 2018-04-2414:49 [PUBDB-2018-01844] Journal Article et al Nanostructured Low Carbon Steels Obtained from the Martensitic State via Severe Plastic Deformation, Precipitation, Recovery, and Recrystallization Advanced engineering materials 2018, 1-8 (2018) [10.1002/adem.201800202]   Restricted: PDF PDF (PDFA); 2018-04-0613:29 [PUBDB-2018-01634] Journal Article et al Toward Optimization of Centrifugal Barrel Polishing P rocedure for Treatment of Niobium Cavities   Centrifugal barrel polishing (CBP) is a simple and environmentally friendly method that can be applied for mechanical abrasion of the cavity interior in order to remove the mechanically damaged surface after its production. The CBP recipes described in the literature, however, require CBP to be performed in many stages, require long processing times and nevertheless are unable to provide good cavity RF performance without additional chemical processing. [...] Fulltext: PDF PDF (PDFA); 2018-04-0314:33 [PUBDB-2018-01618] Poster et al Degradation behaviour and bone responseof resorbable magnesium implants. A 2D and 3D investigation 11 th Annual Workshop of Biofilms – Research Center for Biointerfaces, MalmöMalmö, Sweden, 8 Oct 2015 - 9 Oct 2015 Biodegradable magnesium-alloys are promising implants in orthopedic and cranio-facial surgery to form osteofixation devices that slowly degrade into biocompatible products and do not require a second intervention for removal. However, their degradation needs to be tailored to match the regeneration ability of the bone. [...] Restricted: PDF; 2018-04-0314:12 [PUBDB-2018-01616] Contribution to a conference proceedings et al Corrosion behaviour of 3 Mg-alloys in bone: a high-resolution investigation Biometal - International Symposium of Biodegradable Metals for Biomedical Applications, CarovignoCarovigno, Italy, 23 Aug 2015 - 28 Aug 2015 , 93 pp. (2015)